HO, #8, Crvd Turnout Kit Code 70 Rail, 18/15

This kit does not include rail. If you need rail you can order the same kit with enough rail to build 5 switches.

This kit comes complete with everything you need including:

1 - HO scale, #8, Code 70, 18R/15R, Curved Turnout Assembly Fixture (AF-HO-R-8-ME70-18-15)
1 - Code 70, #8 PointForm Tool (PF-8-M)
5 - HO scale, #8, Curved Turnout Laser Cut Ties (LT-HO-R-8-18-15)
1 - PC Board Ties for HO scale (PB-HO-S)
1 - 18 inch (46 cm) pieces of Micro Engineering code 70 rail (17-070-C)
1 - Small Diameter Solder (SP-0003)
1 - Pliobond Contact Cement with 2 micro dispensing tips (SP-0001)

Need to build more than 5 turnouts? Check below for a list of the items that are included in this kit.

Click on the links below to learn more about how Fast Tracks tools and supplies can help you build better railroads

The complete Assembly Fixture Builders Guide
How the Fast Tracks PointForm tool makes it easy to construct frog & switch points
Using the StockAid tool to file the stock rail
Soldering trackwork - easier than you think!
Have A Question? Visit Our Online Discussion Forum!

Default Turnout Length	14.8" (376 mm)	This is the length of the turnout on the QuickSticks. Measured from end tie to end tie.

Minimum Turnout Length	11.4" (290 mm)	This is the shortest possible turnout length. Measured from the end PC board tie to end PC board tie.

Diverging Route Angle	7.13 (Decimal) 7° / 7' / 48" (D/M/S) 1:8 (Ratio)	Decimal - The frog angle in decimal degrees. D/M/S - The frog angle in Degrees / Minutes / Seconds Ratio - The frog angle expressed as a ratio.

Outside Radius	18R	The radius of the outside route of a curved turnout.

Inside Radius	15R	The approximate radius of the inside route of a curved turnout.

Diverging Route Radius	NA	The minimum radius in a straight turnout.

Tie Spacing (Prototype)	20" (508 mm)	The distance between each tie.

Tie Size (Model)	L - 1.17" (29.7 mm) W - 0.1" (2.6 mm) H - 0.08" (2 mm)	The actual size of the tie.

Tie Size (Prototype)	L - 8.5' (2591 mm) W - 9" (229 mm) H - 7" (178 mm)	The original tie size that the model was based on.

Secondary Frog Angle	NA	The second frog angle for any switch that has two frogs. (Slip switches, 3-ways, dual gauge switches, etc)

Track Gauge	0.66" (16.8 mm)	The distance between the stock rails.

Track Spacing	NA	The center to center distance of the parallel track. (Only applies to double crossovers)

Substitution Radius	NA	The approximate radius that a straight turnout can be inserted into.

Fixture Size (L/W/H)	14" x 6" x 0.25"

Fixture Weight	2 (Lbs)

Fixture Material	6061 Aluminum

This is the first and last videos in our Using Fast Tracks Assembly Fixtures video series. To watch the complete series of videos, visit our video library.

Building Trackwork With Fast Tracks

Completing Trackwork With QuickSticks

Having trouble playing the videos?

If the video starts and stops a lot, try pausing the video for a minute or two by clicking the pause button and then starting it again. This will buffer the video to your computer for smoother playback. If the video will not play at all, be sure you have the latest Flash player from Adobe.

	HO Scale, #8, Curved Turnout Kit for Micro Engineering Code 55 Rail - 24/20"R $222.16
	HO Scale, #6, Curved Turnout Kit for Micro Engineering Code 55 Rail - 30/21"R $212.77
	HO Scale, #8, Curved Turnout Kit for Micro Engineering Code 83 Rail - 18/15"R $216.79
	QuickSticks Laser Cut Ties For N, #4 Turnouts $6.80
	The Last Spike Spiking Pliers - Right Hand $49.95
	N Scale, PC Board Pre-Gapped Crossties - 1mm $18.52
	Z Bend Control Rod to BullFrog Connector $0.40
	NMRA Mark IV, HO Scale, Standards Track Gauge $15.99
	Wire Brush for Cleaning Finished Trackwork $1.99