The Fast Tracks site was moved to a new hosting service on June 15, 2023. For security reasons you will need to reset your account password.

Browse Catalog

QuickSticks Laser Cut Ties For HO, #6 Double Crossovers

LT-HO-C-6
Slide

4 In Stock

We can ship the LT-HO-C-6 immediately. If you order more than what we have available, we will hold your order and add additional units required to our production queue. The lead time for this product is shown above.

PRICE : $12.09

4 in stock

Specially designed for trackwork built with Fast Tracks assembly fixtures, QuickSticks laser cut ties lets you construct fully complete, ready-to-run HO double crossovers right at your workbench!

Using our track assembly fixtures, you build what we call a “skeleton.” This skeleton will have PC Board ties located at key locations to keep the piece of trackwork in gauge. To finish the trackwork, our Laser Cut QuickSticks are used. With a single step, all the remaining wood ties are added to the pre-built skeleton, and the trackwork is ready to be installed.

Now anyone can build inexpensive, hand laid trackwork that:

  • Looks Great! – With realistic-looking trackwork on wood ties
  • Is Easy To Build – With results that rival even the most experienced modelers
  • Performs Perfectly – Build hundreds of double crossovers with one fixture
  • Can Be Built Quickly – Build a complete double crossover in less than an hour!
  • Looks Great! – Get results that rival even the most experienced modelers
  • Lets You Work in Comfort – Build trackwork at your workbench

QuickSticks are cut from Baltic Birch plywood custom sawn in Finland specifically for Fast Tracks. Like the prototype, the wood grain on our QuickSticks ties runs perpendicular to the rails. The ties are 0.08” (2mm), 7 scale inches thick and 0.1” (2.5mm) 9 scale inches wide. They will match all popular commercially available wood ties, including wood ties available from Fast Tracks. The ties will also match all popular commercial track, and trackwork completed with QuickSticks will be compatible with these products.

QuickSticks on this page are the Non-Drilled version. We offer Quicksticks with either drilled or non-drilled wood ties. The version you choose is a matter of personal preference. The non-drilled version has trackwork fastened to it with Pliobond adhesive. Plionbond will provide a solid bond for a lifetime as its bond increases over time and is very reliable. Spiking onto our drilled QuickSticks will provide a mechanical bond that some modelers prefer, but requires a bit more time to install. Not all ties are pre-drilled, only ties at key locations to allow the turnout to be fastened in place.

Gluing non-drilled QuickSticks in place

Gluing QuickSticks to trackwork.

Non-drilled versions of QuickSticks laser cut ties are designed to be glued to the rails using using Pliobond glue. If you prefer, a drilled version is available that is designed to be spiked.

Note: Crossover QuickSticks come in two halves that are joined together when you build the switch.

1 review for QuickSticks Laser Cut Ties For HO, #6 Double Crossovers

  1. 5 out of 5

    Harold Renke (verified owner)

    They match the jig perfectly. Looking forward to building great track work.

Add a review
PARAMETERVALUEDETAILS
Default Turnout Length18.5" (470 mm)This is the length of the turnout on the QuickSticks. Measured from end tie to end tie.
Minimum Turnout Length17.1" (434 mm)This is the shortest possible turnout length. Measured from the end PC board tie to end PC board tie.
Diverging Route Angle9.46 (Decimal)
9°/27'/36"(D/M/S)
1:6 (Ratio)
Decimal = Frog angle in decimal degrees
D/M/S = Deg/Min/Sec
Ratio = Frog angle expressed as a ratio
Diverging Route Radius43" (1092 mm)The minimum radius in a straight turnout.
Tie Spacing (Prototype)20" (508 mm)Tie spacing center of tie to center of tie.
Tie Size (Model)L - 1.17" (30 mm)
W - 0.1" (3 mm)
H - 0.08" (2 mm)
The actual size of the tie.
Tie Size (Prototype)L - 8.5' (2.6 m)
W - 9"(229 mm)
H - 7" (178 mm)
The original tie size that the model was based on.
Secondary Frog Angle19°The second frog angle for any switch that has two frogs.
Track Gauge0.66" (17 mm)The distance between the stock rails.
Track Spacing2" (51 mm)The center to center distance of the parallel track.
SizeL - 12.5" (318 mm)
W - 5.25" (133 mm)
H - 0.08" (2 mm)
The physical size of the product
Weight0.14 lbs (0.064 kg)
Material3 Ply Baltic Birch
Building Turnouts Using Fast Tracks Assembly Fixtures

This fully illustrated document provides complete details for building switches using Fast Tracks tools & supplies. These instructions apply to Turnouts, Wyes & Curved Turnouts in all scales and include essential information for building any fixture-built trackwork.

Completing Switches Using Fast Tracks QuickSticks

This Builders Guide details how to complete building your switch using QuickSticks laser-cut wood ties.

Finishing Straight/Curved Track With QuickSticks

Watch as we demonstrate how to use our QuickSticks laser cut ties to finish straight and curved trackwork built in a Fast Tracks fixture.

Fast Tracks Video Channel

Visit our growing collection of track building demonstration videos

Fast Tracks Knowledge Base

In addition to an extensive Q&A section, we also offer a full library of track building documents.

Items you may want to include in your order​

254 in stock

$7.45

0 in stock

$12.50

PREVIOUSLY VIEWED PRODUCTS